For the highest-quality epoxy flooring installers near you in Fort Myers — industry-leading quality, expert in-house crews, and a lifetime warranty on every floor we coat.
Why Homeowners Across the Southeast Call Apex First for Epoxy Floor Coatings
01
Free Quote
Itemized, up-front pricing for your Fort Myers garage — no pressure, no fake urgency, no surprise add-ons.
02
Diamond-Grind Prep
Every slab gets a mechanical concrete profile first — the step DIY kits and cheap contractors skip.
03
1-Day Install
Walk on it in about 4 hours, park on it in 24 — your garage back to normal by tomorrow.
04
25-Year Warranty
Written and fully transferable, standing behind every floor our Lee County crew installs.
500+Garage Floors
“I’m so happy with my coating! These folks are wonderful at what they do.”
— RODNEY ARNOLD, Google Review
“Elite level flooring from Apex. They use a commercial grade product that lasts a lifetime.”
— CARTER HALL, Google Review
“Apex Epoxy Flooring did a great job on my basement. The crew was easy to deal with and knew what they were doing. Can’t wait to have them do my garage next.”
— ROBERT LAWSON, Google Review
4.7
Based on 14 Google reviews
Industries We Serve
Apex Epoxy Flooring Services & Coatingsfor Fort Myers garages, homes & businesses.
Whatever your floor takes all day, there's an Apex system for it. Hover any industry to see the fit.
Explore our most popular flake, metallic, solid-color and marble finishes. We bring physical samples to every free in-home estimate so you can see them on your slab.
Every layer engineered for Southwest Florida heat, Fort Myers humidity, and the demands of a real garage floor.
01
Prepared Concrete Slabdiamond-ground to CSP-2/3
Your slab, mechanically profiled to a Concrete Surface Profile of 2 to 3, cracks patched and moisture verified. On Lee County's sandy lots we test rather than assume — everything above depends on it.
A pigmented, self-leveling 100%-solids epoxy goes down wet-on-wet across the freshly ground slab, biting into the profile. The film build and color depth here are what separate a genuine coating from a thin painted-on finish.
03
Vinyl Flake Broadcasthand-cast to full rejection
Vinyl flakes are hand-broadcast into the wet basecoat to full rejection. Cured overnight, then scraped flat and vacuumed. Color, camouflage, and underfoot grip, all in one layer.
04
Polyaspartic TopcoatUV-stable, chemical-resistant
What you walk on. This aliphatic polyaspartic topcoat seals the flake and holds its color under Southwest Florida's relentless UV, shrugging off Gulf salt air, brake fluid, and hot tires. The 25-year warranty starts here.
From Free Estimate to Final Walk-Through
1
Free Estimate
A free, no-pressure in-home quote with real color samples.
2
Diamond Grind
We mechanically diamond-grind your slab to the right profile.
3
Application
100% solids epoxy, flake broadcast, and polyaspartic topcoat.
4
Final Walk-Thru
We walk the finished floor with you before we leave.
Ready to book your free estimate?
Free in-home consultation with real color samples — most Fort Myers jobs quoted same day.
Your price comes down to the finish you choose and the condition of your slab. These are honest, installed starting prices for a typical Fort Myers 2-car and 3-car garage.
Finish
Starting Price
2-Car (~450 sq ft)
3-Car (~650 sq ft)
Best For
Solid Epoxy
$4per sq ft
~$1,800
~$2,600
Clean, budget-friendly single color
Flake EpoxyMost Popular
$6per sq ft
$2,700$2,300
$3,900$2,700
Most garages — hides flaws, adds grip
Quartz Epoxy
$6per sq ft
~$2,700
~$3,900
Maximum slip resistance & durability
Metallic Epoxy
$9per sq ft
~$4,050
~$5,850
High-end, marbled showpiece look
Final pricing confirmed with your free in-home estimate — no pressure, no games.
Serving the Greater Fort Myers, FL Area
Epoxy Flooring Near Me
Professional epoxy & garage floor coatings across Fort Myers and the surrounding Southwest Florida communities.
Cape CoralEsteroBonita SpringsLehigh AcresFort Myers BeachSanibelGatewaySan Carlos ParkNorth Fort MyersPunta RassaIonaWhiskey CreekMcGregorVillasCypress LakeFort Myers ShoresTice
Upgrade Your Fort Myers Garage Floor in 1 Day - Free Estimate
Book Your Trusted Fort Myers Epoxy Flooring Contractor - Free Quote
Free Consultation
Contact us today for a no-cost consultation where we evaluate your flooring needs, provide an estimated price based on square footage, and recommend the best epoxy flooring solutions tailored specifically for you.
Diamond Grinding Floor Prep
We use a diamond propane grinder to meticulously prepare your floor, ensuring a smooth, flawless surface that maximizes the adhesion and longevity of your epoxy floor coating.
Multi-Layered Epoxy Floor Installation
Our team applies multiple layers of premium epoxy resin flooring, each layer enhancing the durability, aesthetics, and overall performance of your new epoxy floor.
Curing & Final Inspection
We ensure the epoxy floor coating cures properly to achieve maximum strength and conduct a thorough final inspection to guarantee your complete satisfaction with the finished project.
You don’t have to choose. We lay a 100% solids epoxy base for depth, then seal it with a polyaspartic topcoat for speed and UV resistance — the best of both.
Fort Myers Epoxy FAQs
Answers From Our Epoxy Flooring Professionals
The questions Fort Myers homeowners actually search before coating a garage floor — answered honestly, including the downsides.
A typical Fort Myers 2-car garage runs $1,800 to $2,700 installed; our flake system is a flat $2,300 for a 2-car, $2,700 for a 3-car. Professional coatings generally run $5–$15 per square foot, the spread set by the system and how much prep the slab needs — on some Lee County lots that means a moisture test and a vapor-barrier primer. You leave your free in-home estimate with a firm number, not a range.
At roughly 400 square feet, a 20×20 slab is standard 2-car territory, so our flake system lands in the $2,300 range when the concrete is in normal shape. Sandy Southwest Florida soils allow minor settlement, so if we find heavy cracking, pitting, or an old failing coating that has to come off, that adds labor — and you’ll hear it up front, not after the grinders are running.
Nationwide, a professional 2-car install averages $1,500–$4,000, while a big-box DIY kit is $300–$900. Here in the Fort Myers area, most jobs settle into the $1,870–$2,700 band. A quote far under that usually signals thin material, an acid etch instead of diamond grinding, or a single-coat product that won’t survive our year-round heat and humidity.
Almost always, it comes down to prep. A $900 quote buys a roller, a bucket, and an afternoon — no grinding, no moisture testing, no crack repair. A real quote covers diamond-grinding the slab to a CSP 2–3 profile, patching cracks, and verifying moisture, which matters here since a shallow wet-season water table can push vapor up through a Lee County slab. That prep is why one floor lasts decades and another peels in two.
Everything: diamond-grind prep, crack and pit repair, slab moisture testing, a 100%-solids pigmented epoxy basecoat, a full vinyl flake broadcast, a UV-stable polyaspartic topcoat, and a written, transferable 25-year warranty. No trip charges anywhere in Lee County, and no surprise add-ons once the work has started.
Compared with tile, generally yes — tile costs more to install, and its grout lines crack and stain fast in a working garage. Against polished concrete the price is roughly comparable, but a coated floor adds color, flake, and a sealed, non-porous surface that shrugs off oil and chemicals — something bare polished concrete in a humid Fort Myers garage simply can’t do.
Installed properly, it’s well worth it. You trade a dusty, staining slab for a sealed, non-porous surface you can sweep or hose down — one that resists oil, brake fluid, and hot tires and makes the whole garage read as finished space. The value hinges entirely on preparation; a coating sprayed over an unground slab is money thrown away.
Straight talk: a cheap floor can peel, un-topcoated epoxy can amber under direct sun, and any smooth coating turns slick when wet. Each one has a fix — diamond grinding locks in the bond, a UV-stable polyaspartic topcoat holds color through relentless year-round sun, and a full flake broadcast gives the surface genuine grip. The downsides are real; they’re also every bit as solvable.
When the slab is working against you. Depending on the lot, a shallow wet-season water table in our sandy Lee County soil can push vapor up through the concrete — and if that, or major structural cracking or heaving, goes unaddressed, coating over it only traps the problem. That’s why we moisture-test before quoting. If your slab isn’t a candidate, we’ll say so rather than sell you a floor that will fail.
A smooth, high-gloss coating can be, yes. That’s why our flake and quartz systems cast decorative chips into the wet basecoat, leaving a fine texture that grips underfoot — you feel it the moment you pull a rain-soaked car in during a Southwest Florida summer downpour. For wash-down zones we can broadcast extra slip aggregate.
It won’t appraise like a kitchen remodel, but few upgrades add this much visible value for the money — a finished floor photographs beautifully, signals a well-kept home, and Fort Myers buyers notice it right away. The 25-year warranty transfers with the sale, and in a flood-aware market a sealed, easy-to-clean floor is a real selling point.
Expect 10–20 years from a professionally installed floor, and longer still when the slab was ground and moisture-tested the right way. Big-box DIY kits usually start peeling or yellowing inside 2–5 years — they’re thin, water-based, and rolled over an unground slab. In relentless heat and humidity that gap only widens. Every Apex system carries a written 25-year warranty.
Five years in, a properly prepped flake floor reads almost like day one — at most a touch less gloss along the main tire path. A floor that skipped real prep tells the opposite story: patches lifting where cars park, chips along the door line, and ambering anywhere the Fort Myers sun reaches it through an open door.
Not when the prep is done right. Industry data on epoxy failures is blunt: up to 80% trace back to poor surface preparation. Peeling and hot-tire pickup come from a weak bond; bubbling comes from moisture driving up through the slab — a real concern on Lee County’s sandy, high-water-table lots. We diamond-grind to a CSP 2–3 profile and moisture-test every slab, priming with a vapor barrier where readings call for it.
Bare epoxy does amber under UV over time — that’s chemistry, not poor workmanship. It’s the reason we never leave epoxy as the surface you see. The aliphatic polyaspartic topcoat is UV-stable and non-yellowing, so the floor holds its color under intense, year-round sun — even with the garage door open all day in July.
Yes. Hot-tire pickup happens when warm rubber grabs a soft or weakly bonded coating and lifts it. Our polyaspartic topcoat stays hard through Southwest Florida’s heat and is locked to a diamond-ground slab, so tires roll off clean.
Neither wins alone — they win as a pair, which is why we run both. The epoxy layer buys film thickness, color depth, and a deep mechanical bite into the slab. The polyaspartic layer cures fast, resists chemicals, and holds its color under Southwest Florida’s year-round UV. So we roll a 100%-solids epoxy base, broadcast the flake, and seal it under a polyaspartic topcoat — each material covering the other’s weakness.
For the wear layer, yes — polyaspartic beats epoxy on UV stability, cure time, and hot-tire pickup under a relentless Fort Myers sun. For the base layer, a 100%-solids epoxy still gives the best film build and bond for the money. Anybody pushing a one-product floor is trimming their own labor, not protecting your slab.
Durability comes from layers, not a single bucket. The toughest floor is a stack: mechanically ground slab, 100%-solids epoxy base, a full flake or quartz broadcast, and a polyaspartic wear layer. Longevity comes down to total film thickness and bond strength — not the brand printed on the label.
You can, and on a light-use slab a kit might last a few years. Here’s the honest tradeoff: big-box kits are thin, usually water-based, and lean on an acid etch instead of mechanical grinding — which is exactly why so many peel in 2–5 years. Once you add up the grinder rental, the materials, and a weekend of your labor, the DIY route often costs more than people expect and lands close to a professional quote.
Only once the old coating has been handled properly. If it’s lifting, new epoxy on top just inherits that failure. We grind the old system off, back to sound concrete, then moisture-test the bare slab — which matters on Fort Myers slabs where vapor drives up from below. It adds labor, and we’ll price that honestly at the estimate.
Nearly every Fort Myers residential garage wraps up in a single day. We diamond-grind and prep in the morning, then roll the basecoat, broadcast the flake, and seal it with the polyaspartic topcoat the same afternoon. A larger commercial or industrial slab in the area can run two days — either way you’ll have the schedule before we start.
Plan on walking across it in roughly 4 hours and pulling the car back in at 24. That quick turnaround comes straight from the polyaspartic topcoat — a plain epoxy floor would lock you out of the garage for the better part of a week.
A complete build: a moisture-mitigating primer wherever a Southwest Florida slab reads damp, then a pigmented 100%-solids epoxy basecoat rolled corner to corner, vinyl flake broadcast until the surface won’t take more, and finally a clear polyaspartic topcoat. Between the flake and that topcoat we scrape and vacuum the surface perfectly flat.
A dust-mop or broom handles the day-to-day, and a hose or damp mop with mild cleaner takes care of the rest. Skip the wax, the sealer, the specialty bottles — none of it is needed. The coating is non-porous, so oil, brake fluid, and Gulf-coast grime rest on the surface and wipe off instead of soaking in.
Absolutely. A single gouge — a dropped jack stand, the corner of a rolling toolbox — gets spot-repaired and feathered in without touching the rest of the floor. That’s the quiet advantage of a flake system: the multicolored pattern swallows the patch until it’s all but invisible.
Whenever suits you. Polyaspartic cures over a broad temperature band and the job happens inside your Lee County garage, so a humid August or a January cool snap never stops us. What we do check every month is slab moisture — in Southwest Florida’s sandy, moisture-prone soils that reading matters far more than the calendar.
Mostly at install time — which is why we test rather than assume. In Lee County’s sandy flatwoods the wet-season water table can sit high under a garage slab, so soil moisture keeps driving vapor up through the concrete; trap that under a film with no barrier and blistering or delamination shows up later. It comes down to which lot you’re on, so we moisture-test every slab and prime with a vapor barrier wherever the readings call for it.
Salt air goes after porous surfaces — it works into bare or lightly sealed concrete and pits it over time. A seamless, non-porous, fully bonded system gives Gulf chlorides nothing to grab, which is why we build the same way for a salt-exposed garage out on Fort Myers Beach or Sanibel as we do for an inland Lehigh Acres or Gateway home.
Not under a properly installed one. Mold needs both moisture and a food source, and a fully bonded, non-porous coating laid over a moisture-tested slab leaves no pocket where water can sit and feed it. The trouble only shows up when a floor goes down over a damp slab with no vapor barrier — exactly the failure our moisture testing exists to catch first.
Yes — across all of Lee County. That’s Fort Myers itself plus Cape Coral, Estero, Bonita Springs, Lehigh Acres, Fort Myers Beach, Sanibel, Gateway, San Carlos Park, North Fort Myers, Punta Rassa, Iona, Whiskey Creek, McGregor, Villas, Cypress Lake, Fort Myers Shores, and Tice. Live just outside that list? Call us at (239) 392-4787 and ask — odds are we cover your area too.
Customer Reviews
Apex Reviews From Southwest Florida
4.7Based on 14 Google reviews
MMichael West5 months ago
Great business would definitely recommend it very nice ppl and they do amazing work
TTessa Monroe6 months ago
Found Apex while I was looking online for a epoxy installer. I gave them a call and the owner Blake personally came out to give me the quote on the 1,200 square foot interior. We agreed on a price and they got to work. The job took 3 days wo complete with the first being leveling and grinding of the pavement. The marble look turned out stunning. The look is beautiful and durable against the dogs nails. Thanks so much again Blake, great job on the floor.
JJackson Bennett7 months ago
I was so upset with the last company I hired for my garage and kitchen floors. My garage floor started cracking, and they claimed it was normal, but the cracks kept growing every month. It was clear they weren’t legit. Taking another chance, I hired Apex, and luckily, Blake came through and fixed my garage floor perfectly. Thank you, Apex!
Update: had to circle back and let everyone know that after 10 months the kitchen and garage still look like they did when the team installed it from day one. 👍
AAshley Hall7 months ago
Blake put a marble swirl epoxy in my living room, dinning room and master bed room of the house which was roughly 1,200 sqft. It took the guys three days to do all different layers and it turned out AMAAAAZING!! Fast, professional and kind service with Apex.
KKenneth Rodriguez7 months ago
Really happy with the 3 car garage floor this company put in. It turned out just like the photos with really no mess. Well worth it to install an epoxy flooring the garage.
CCalliope Sage9 months ago
Apex redid our kitchen floor with a polyaspartic coating. It dried fast and doesn't hold grease like tiles used to. The grip is good and cleaning takes no time now. Works perfect for a busy kitchen.
For just $2,700, give your 3-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
2 Car Garage floors for Just $2300
For just $2,300, give your 2-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
3 Car Garage Flooring for Just $2700
For just $2,700, give your 3-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
2 Car Garage floors for Just $2300
For just $2,300, give your 2-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
Get Started Now
Ready to upgrade your garage with Apex Epoxy Flooring? Fill out the form below, and let us handle the rest. Whether it’s a 2-car or 3-car garage, we’re here to deliver top-notch service.
Most popular
