For the highest-quality epoxy flooring installers near you in Hialeah — industry-leading quality, expert in-house crews, and a lifetime warranty on every floor we coat.
Why Homeowners Across the Southeast Call Apex First for Epoxy Floor Coatings
01
Free Quote
Clear, itemized pricing on your Hialeah garage — no pressure, no fake urgency, no hidden add-ons.
02
Diamond-Grind Prep
A true mechanical concrete profile on every slab — the prep step DIY kits and cheap contractors skip.
03
1-Day Install
Walk on it in roughly 4 hours, drive on it in 24, and you're back to normal by tomorrow.
04
25-Year Warranty
Written and fully transferable, honored by the local Apex crew that coated your Miami-Dade floor.
500+Garage Floors
“I’m so happy with my coating! These folks are wonderful at what they do.”
— RODNEY ARNOLD, Google Review
“Elite level flooring from Apex. They use a commercial grade product that lasts a lifetime.”
— CARTER HALL, Google Review
“Apex Epoxy Flooring did a great job on my basement. The crew was easy to deal with and knew what they were doing. Can’t wait to have them do my garage next.”
Explore our most popular flake, metallic, solid-color and marble finishes. We bring physical samples to every free in-home estimate so you can see them on your slab.
Every layer engineered for South Florida heat, Hialeah humidity, and the demands of a real garage floor.
01
Prepared Concrete Slabdiamond-ground to CSP-2/3
The slab you already have, diamond-ground to a Concrete Surface Profile of 2 to 3. Cracks patched, and moisture tested—non-negotiable on Miami-Dade slabs over shallow limestone. Nothing above lasts unless this layer is right.
A pigmented, self-leveling 100%-solids epoxy, rolled wet-on-wet straight onto the freshly ground slab. This layer builds the color depth and film thickness that separate a real floor from a coat of paint.
03
Vinyl Flake Broadcasthand-cast to full rejection
Vinyl flake chips hand-broadcast into the wet basecoat until it takes no more. Cured overnight, then scraped flat and vacuumed. One step delivers color, camouflage for wear, and grip underfoot.
04
Polyaspartic TopcoatUV-stable, chemical-resistant
The surface you actually walk on. This aliphatic polyaspartic topcoat seals the flake and shrugs off Hialeah’s year-round UV and heat, brake fluid, chemicals, and hot tires. Your 25-year warranty starts at this layer.
From Free Estimate to Final Walk-Through
1
Free Estimate
A free, no-pressure in-home quote with real color samples.
2
Diamond Grind
We mechanically diamond-grind your slab to the right profile.
3
Application
100% solids epoxy, flake broadcast, and polyaspartic topcoat.
4
Final Walk-Thru
We walk the finished floor with you before we leave.
Ready to book your free estimate?
Free in-home consultation with real color samples — most Hialeah jobs quoted same day.
Your price comes down to the finish you choose and the condition of your slab. These are honest, installed starting prices for a typical Hialeah 2-car and 3-car garage.
Finish
Starting Price
2-Car (~450 sq ft)
3-Car (~650 sq ft)
Best For
Solid Epoxy
$4per sq ft
~$1,800
~$2,600
Clean, budget-friendly single color
Flake EpoxyMost Popular
$6per sq ft
$2,700$2,300
$3,900$2,700
Most garages — hides flaws, adds grip
Quartz Epoxy
$6per sq ft
~$2,700
~$3,900
Maximum slip resistance & durability
Metallic Epoxy
$9per sq ft
~$4,050
~$5,850
High-end, marbled showpiece look
Final pricing confirmed with your free in-home estimate — no pressure, no games.
Serving the Greater Hialeah, FL Area
Epoxy Flooring Near Me
Professional epoxy & garage floor coatings across Hialeah and the surrounding South Florida communities.
Upgrade Your Hialeah Garage Floor in 1 Day - Free Estimate
Book Your Trusted Hialeah Epoxy Flooring Contractor - Free Quote
Free Consultation
Contact us today for a no-cost consultation where we evaluate your flooring needs, provide an estimated price based on square footage, and recommend the best epoxy flooring solutions tailored specifically for you.
Diamond Grinding Floor Prep
We use a diamond propane grinder to meticulously prepare your floor, ensuring a smooth, flawless surface that maximizes the adhesion and longevity of your epoxy floor coating.
Multi-Layered Epoxy Floor Installation
Our team applies multiple layers of premium epoxy resin flooring, each layer enhancing the durability, aesthetics, and overall performance of your new epoxy floor.
Curing & Final Inspection
We ensure the epoxy floor coating cures properly to achieve maximum strength and conduct a thorough final inspection to guarantee your complete satisfaction with the finished project.
You don’t have to choose. We lay a 100% solids epoxy base for depth, then seal it with a polyaspartic topcoat for speed and UV resistance — the best of both.
Hialeah Epoxy FAQs
Answers From Our Epoxy Flooring Professionals
The questions Hialeah homeowners actually search before coating a garage floor — answered honestly, including the downsides.
In Hialeah, most 2-car garages come in between $1,800 and $2,700 installed. Our flake system is $2,300 for a 2-car and $2,700 for a 3-car, all-in — no line-item surprises. Across the industry, professional coatings run roughly $5–$15 per square foot, driven mostly by the system you choose and how much the slab needs before coating. You leave your free in-home estimate holding one firm number, not a spread.
At roughly 400 square feet, a 20×20 garage falls squarely in standard 2-car territory. That puts it in our $2,300 flake range, provided the slab is in normal condition. Heavy cracking, pitting, or an old failing coating that has to be ground off will push the number up — and you’ll hear about that before we begin, never midway through.
Across the country, a professional 2-car install averages $1,500–$4,000, while a DIY kit lands around $300–$900. Here in Hialeah, real quotes tend to sit in the $1,870–$2,700 band. When a bid comes in far under that, it almost always signals thin material, an acid etch in place of diamond grinding, or a single-coat product that won’t go the distance.
Almost always because of prep. A $900 quote is a roller, a bucket, and an afternoon — no grinding, no moisture testing, no crack repair. A proper quote includes mechanically diamond-grinding the slab to a CSP 2–3 profile, patching cracks, and verifying moisture. That prep is the single biggest reason one floor lasts 20 years and another peels in two.
All of it: diamond-grind preparation, crack and pit repair, moisture testing, a 100%-solids pigmented epoxy basecoat, a full vinyl flake broadcast, a UV-stable polyaspartic topcoat, and a written, transferable 25-year warranty. There are no trip fees and no add-ons that surface after the work is finished.
Compared with tile, usually yes — tile runs more to install, and its grout lines crack and stain fast in a garage. Set against polished concrete the cost is roughly even, but a coating adds color, flake, and a non-porous surface that shrugs off oil and chemicals — something bare polished concrete simply can’t do.
Done right, absolutely. A bare Hialeah slab sheds dust and drinks up every oil drip; a sealed, non-porous coating flips that entirely — you sweep or hose it clean, it shrugs off brake fluid and hot tires, and the garage finally reads as finished square footage. But the worth lives entirely in the prep. Spray a coating over an unground slab and the money is simply gone.
The honest downsides: a bargain epoxy floor can peel, uncoated epoxy can amber under direct sun, and any glass-smooth coating turns slick when wet. All three are solvable, and we solve each one — diamond grinding for a true mechanical bond, a UV-stable polyaspartic topcoat that keeps its color, and a full flake broadcast that puts real grip underfoot. The downsides are real; so are the fixes.
If the slab has active moisture intrusion coming up from below, or major structural cracking or heaving that hasn’t been addressed, coating over it just traps the problem. That’s why we moisture-test before quoting. If your slab isn’t a candidate, we’ll tell you rather than sell you a floor that will fail.
A slick, glossy film can be, yes. Our flake and quartz systems solve it at the source: decorative chips broadcast into the wet basecoat leave a subtle underfoot texture that grips — which matters the moment you roll a dripping car in during a Hialeah wet-season downpour. For areas that get hosed down, we can add extra slip aggregate for more bite.
No, it won’t appraise like a new kitchen — but few upgrades return this much visible payoff for the money. A finished garage floor photographs well, tells buyers the home has been cared for, and gets noticed the second someone steps inside. And because our warranty transfers to the next owner, it reads as a genuine selling point rather than just a nice finish.
A professionally installed system runs 10–20 years, and longer still when the prep was done right — even under Hialeah’s year-round UV and heat-island load. Big-box DIY kits usually start peeling or yellowing inside 2–5 years because they’re thin, water-based, and rolled over an unground slab. Every floor we install across Miami-Dade carries a written 25-year warranty.
At five years, a properly installed flake floor looks essentially like day one — perhaps a touch less gloss along the main tire path. A poorly prepped floor tells the opposite story by then: patches lifting where the tires park, chips along the door line, and yellowing anywhere the sun reaches. The finish that holds is the one ground and sealed correctly the first time.
Not when the prep is done right. The industry data on epoxy failures is blunt: up to 80% of failures trace back to poor surface preparation. Peeling and hot-tire pickup come from a weak bond; bubbles come from trapped moisture — and on Hialeah’s oolitic-limestone slabs sitting over a shallow, high water table, that vapor drive is very real. We diamond-grind to a CSP 2–3 profile and moisture-test every slab so neither problem gets a foothold.
Straight epoxy ambers over time under UV — that’s chemistry, not workmanship. It’s exactly why we never leave epoxy as the wear layer. Our polyaspartic topcoat is UV-stable, so the color holds even under Hialeah’s relentless year-round sun and heat-island glare, with the garage door open all afternoon in July.
Yes. Hot-tire pickup happens when hot rubber grabs a soft or poorly bonded coating and peels it up. Our polyaspartic topcoat stays rock-hard through relentless South Florida heat and is locked to a diamond-ground slab, so tires roll off it clean instead of dragging the finish with them.
It’s the wrong question — the two do different jobs, so we run them as a team. Epoxy brings film thickness, color depth, and a strong mechanical bite into the slab. Polyaspartic cures fast and, more to the point under Hialeah’s year-round UV, holds its color and resists chemicals. We pour a 100%-solids epoxy base, broadcast flake, and lock it under a polyaspartic topcoat — each material’s strength, neither one’s weakness.
Depends which layer you mean. As a wear layer, yes — polyaspartic beats epoxy on UV stability, cure speed, and hot-tire resistance. As a basecoat, a 100%-solids epoxy still gives the best film build and bond for the money. Anyone pushing a single-product floor is optimizing their own labor, not your slab.
The most durable floor is a multi-layer stack, not one product — a mechanically ground slab, a 100%-solids epoxy base, a full flake or quartz broadcast, and a polyaspartic wear layer. On a Miami-Dade slab, total film thickness and bond quality matter more than the brand on the bucket.
You can, and on a light-use slab a kit might last a few years. Here’s the honest tradeoff: big-box kits are thin, usually water-based, and rely on an acid etch instead of mechanical grinding — which is why most fail within 2–5 years. Once you tally grinder rental, materials, and a lost weekend, the DIY route often lands closer to a professional quote than people expect.
Only once the old coating has been handled the right way. If the existing floor is already lifting or delaminating, laying new epoxy over it just inherits that failure. We diamond-grind the old system back to sound concrete and rebuild from a clean profile. That adds labor — and we’ll price it honestly at your Hialeah estimate.
Nearly every residential garage is a single-day install. The morning is diamond-grinding and prep; that same afternoon we roll the basecoat, broadcast the flake, and seal it with the polyaspartic topcoat. The bigger light-commercial and warehouse slabs common around Hialeah and nearby Medley can stretch to two days — either way, you’ll have the schedule in hand before we start.
Foot traffic is fine in roughly 4 hours, and you can pull the car back in at 24. That quick turnaround comes straight from the polyaspartic topcoat doing its job — a plain epoxy floor would lock you out of the garage for the better part of a week.
A complete layered system: a vapor-barrier primer where the slab’s moisture readings call for one — not unusual on Hialeah’s high-water-table slabs — then a pigmented 100%-solids epoxy basecoat rolled corner to corner, vinyl flake broadcast to rejection, and a clear polyaspartic topcoat. The flake is scraped and vacuumed dead flat before that topcoat goes on.
Sweep or dust-mop it, then hose or damp-mop with a mild cleaner as needed — no wax, no resealing, no specialty products. Because the surface is non-porous, oil and brake fluid rest on top and wipe away instead of soaking in. After a Miami-Dade wet-season storm tracks grit inside, a quick rinse sets it right.
Yes. A single point of damage — a dropped jack stand, a toolbox gouge — gets spot-repaired and feathered in without recoating the whole slab. That’s one of the quiet advantages of a flake floor: the mottled pattern swallows the patch so you’d be hard-pressed to find it.
Any month works. Polyaspartic cures across a broad temperature range and the whole job happens inside your garage, so Hialeah’s heavy summer humidity doesn’t stop us — and with no real freeze here, cold snaps never enter the picture. We do moisture-test year-round, because slab moisture matters far more than the calendar.
It affects the installation, which is why we test for it. South Florida slabs carry real moisture vapor drive, and coating over it without a barrier is what causes bubbling and delamination later. We moisture-test every slab and use a vapor-barrier primer where the readings call for it.
It can if a slab isn’t handled right. Much of Hialeah sits on Miami-Dade’s limestone with a shallow water table, so moisture drives up through the concrete. Coat over that without addressing it and vapor pressure lifts the film, causing bubbling and delamination. That’s why we moisture-test every slab and use a vapor-barrier primer wherever the readings call for it — the step that keeps a floor bonded here.
Not under a properly installed system. Mold needs moisture and a food source; a fully bonded, non-porous coating over a moisture-tested slab leaves no gap for water to collect. Problems arise when a coating is applied over a damp slab with no barrier — the exact failure our moisture testing exists to prevent.
Yes — Hialeah proper, plus Miami Lakes, Miami Springs, Opa-locka, Doral, Medley, Hialeah Gardens, Miami, Palm Springs North, Country Club, Westview, Brownsville, Gladeview, Miami Gardens, Virginia Gardens, West Little River, Golden Glades, and Norland. Don’t see your neighborhood? If you’re nearby in Miami-Dade, call (786) 460-0087 and we’ll let you know.
Customer Reviews
Apex Reviews From South Florida
5Based on 6 Google reviews
CChloe Graham7 months ago
They put redid a good chunk of the flooring in the plant with a white epoxy that works well for the area. All the walk lines are straight and they use a good material so we know it will last. These guys do good work.
MMichael Johnson11 months ago
Beautiful job and very professional workers. They did the three car garage without a single blemish in the application. Blake and his team at Apex Epoxy Flooring are wonderful to have for epoxy work.
AAlice Johnsona year ago
On time and fantastic work and finish, highly recommend Blake and his team at Apex Epoxy Flooring of Hialeah.
For just $2,700, give your 3-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
2 Car Garage floors for Just $2300
For just $2,300, give your 2-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
3 Car Garage Flooring for Just $2700
For just $2,700, give your 3-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
2 Car Garage floors for Just $2300
For just $2,300, give your 2-car garage a professional epoxy flooring finish backed by our lifetime warranty. Fill out this form below to take advantage of this limited time offer!
Get Started Now
Ready to upgrade your garage with Apex Epoxy Flooring? Fill out the form below, and let us handle the rest. Whether it’s a 2-car or 3-car garage, we’re here to deliver top-notch service.
Most popular
